Good quality Certanium Welding Rod - Stainless Steel Welding Electrode AWS E312-16 – Tianqiao

Short Description:

Product Detail

Product Category

Product Tags

Feedback (2)

We normally follow the basic principle Quality Initial, Prestige Supreme. We've been fully committed to offering our consumers with competitively priced good quality merchandise, prompt delivery and professional support for Super 60 Welding Rod , 304 Welding Rod , 7018 Ac , We sincerely welcome domestic and foreign merchants who calls, letters asking, or to plants to negotiate, we will offer you quality products and the most enthusiastic service,We look forward to your visit and your cooperation.

Good quality Certanium Welding Rod - Stainless Steel Welding Electrode AWS E312-16 – Tianqiao Detail:

APPLICATIONS:

Used for welding high carbon steel, tool steel and dissimilar metals

CHARACTERISTICS:

E312-16 is a duplex stainless steel electrode with a titanium-calcium coating. The welding process performance is excellent, and it can be used for both AC and DC. Because the weld contains about 40% of ferrite, it has excellent crack resistance

ATTENTION:

1. Before welding, the electrode shall be baked at 300-350℃ for 1 hour and used as needed.
2. Remove rust, grease, moisture and other impurities before welding.
3. For welding hardenable steel, when using small current to weld complex and thick workpieces, the workpieces should be preheated at 150℃.

WELDING POSITIONS:

PA, PB, PD, PF

Chemical Composition Of All Welding Metal: (Wt. %)

Items	C	Mn	Si	S	P	Ni	Cr	Mo	Cu
Requirements	0.15	0.5-2.5	≤1.0	≤0.03	≤0.04	8.0-10.5	28.0-32.0	≤0.75	≤0.75
Typical Results	0.09	1.08	0.76	0.010	0.028	9.97	29.0	0.12	0.17

MECHANICAL PROPERTIES OF ALL WELD METAL:

Items	Rm/MPa	A/%
Requirements	≥660	≥15
Typical Results	760	28

TYPICAL OPERATING PROCEDURES: (AC or DC+)

Diameter (mm)	2.5	3.2	4.0	5.0
Length (mm)	300	350	400	400
Current (A)	50-80	80-110	130-160	160-200

PACKAGING:

5kg/box, 4boxes/carton, 20kgs/carton, 50cartons/pallet. 21MT -26MT per 1X20″ FCL.

Material requirements for welding parts:

The steel numbers, specifications and ordering requirements of the raw materials of the welding parts shall comply with the requirements of the drawings or technical documents, and the material substitution system shall be strictly implemented for the substitution of materials.

The materials of the welding parts (steel plate, steel, welding rod, welding wire, flux and shielding gas, etc.) shall be inspected and accepted according to the relevant material standards when entering the factory. Materials that cannot be confirmed or have no certificate of conformity must be re-inspected. Can be used.

When selecting welding rods, wires, fluxes and shielding gases for welding parts, it should be based on the principle of equal strength between the weld metal and the base metal to ensure that the weld metal is not lower than the mechanical properties of the base metal, and should comply with the standard GB/ T 5117, GB/T 5118 and GB/T 8110.

Welding rods and fluxes with special instructions should be dried in accordance with the requirements of the instruction manual. The drying temperature without special requirements should meet the requirements of the table. Store it in an incubator after drying, and take it out when you need it. The welding rod should not be baked more than twice. The welding wire must be cleaned of oil and water before use.

Product detail pictures:

Related Product Guide:
The composition of the welding electrode

It really is our obligation to satisfy your requirements and efficiently serve you. Your fulfillment is our greatest reward. We're hunting forward to your check out for joint development for Good quality Certanium Welding Rod - Stainless Steel Welding Electrode AWS E312-16 – Tianqiao, The product will supply to all over the world, such as: Mombasa, Bhutan, Colombia, We rely on high-quality materials, perfect design, excellent customer service and the competitive price to win the trust of many customers at home and abroad. 95%products are exported to overseas markets.